rf ht-radio-profile

rf ht-radio-profile <profile>

40MHz-intolerance

bss-color <bss-color>

bss-color-switch-count

clone <profile>

csd-override

honor-40MHz-intolerance

vht-bw-signaling

vht-txbf-sounding-interval

Description

This command configures high-throughput AP radio settings. High-throughput features use the IEEE 802.11n standard, which supports 40 MHZ channels and operates in both the 2.4 GHZ and 5 GHZ frequency bands.

Most transmissions to high throughput (HT) stations are sent through multiple antennas using cyclic shift diversity (CSD). When you enable the disable-diversity-spreading parameter, CSD is disabled and only one antenna transmits data, even if they are being sent to high-throughput stations. Use this feature to turn off antenna diversity when the AP must support legacy clients such as Cisco 7921g VoIP phones, or older 802.11g clients (e.g. Intel Centrino clients). Note, however, that enabling this feature can reduce overall throughput rates.

The ht-radio-profile you wish to use must be assigned to a dot11a and/or dot11g-radio-profile. You can assign the same profile or different profiles to the 2.4 GHZ and 5 GHZ frequency bands. See rf dot11a-radio-profile on page 1 and rf dot11g-radio-profile on page 1.

Parameter	Description
<profile>	Name of this instance of the profile. The name must be 1-63 characters. Default Options: “Default-a” is generally used in association with high-throughput devices running on the 5 GHz frequency band, see rf dot11a-radio-profile on page 1. “Default-g” is generally used in association with high-throughput devices running on the 2.4 GHz frequency band, see rf dot11g-radio-profile on page 1. “Default” is generally used when the same ht-radio-profile is desired for use with both frequency bands. Default: default-a, default-g, default
40MHz- intolerance	Controls whether or not APs using this radio profile will advertise intolerance of 40 MHz operation. By default, 40 MHz operation is allowed. Default: disabled
bss-color	Enables different colors for each category of BSSIDs. The HPE Aruba Networking 802.11ax based access points like AP-505, AP-515, AP-534. AP-535 and AP-555 support BSS coloring mechanism that helps identify the BSS from which a PLCP protocol data unit originates. NOTE: 530 Series and 550 Series access points can detect and change the color automatically if the same color is detected for another BSS on the same channel. NOTE: The value of 0 means auto mode, that is, the AP will set the color by itself, finding any available color. Range: 0-63 Default: 0
bss-color-switch-count	The number of times the BSS color switch announcements are sent in beacons before switching to a new color. Range: 0-100 and the default value is 10. Range: 0-100 Default: 10
clone	Name of an existing high-throughput radio profile from which parameter values are copied.
csd-override	Override Cyclic Shift Diversity for better interoperability.
honor-40MHz- intolerance	When enabled, the radio will stop using the 40 MHz channels if the 40 MHz intolerance indication is received from another AP or station. Default: enabled
no	Negates any configured parameter.
vht-bw-signaling	Enable VHT Bandwidth Signaling RTS for better interoperability (802.11ac APs only). Default: Disabled
vht-txbf-sounding-interval <vht-txbf-sounding-interval>	Time interval in milliseconds between updates of VHT Transmit Beamforming channel estimation. (802.11ac APs only). Default: 0

Example

The following command configures an ht-radio-profile named “default-g” and enables 40MHz-intolerance:

(host)[node](config) #rf ht-radio-profile default-g

40MHz-intolerance

Command History

Release	Modification
AOS 8.6.0.0	The `bss-color-switch-count` parameter was added.
AOS 8.4.0.0	The `bss-color` parameter was added.
AOS 8.0.0.0	Command introduced.

Command Information

Platforms	License	Command Mode
All platforms, but operates with IEEE 802.11n compliant devices only	Base operating system.	Config mode on Mobility Conductor.