show ap monitor debug

counters {ap-name <ap-name>}|{bssid <bssid>}|{ip-addr <ip-addr>}|{ip6-addr <ip6-addr>}

profile-config {ap-name <ap-name>}|{bssid <bssid>}|{ip-addr <ip-addr>}|{ip6-addr <ip6-addr>}

status {ap-name <ap-name>}|{bssid <bssid>}|{ip-addr <ip-addr>}|{ip6-addr <ip6-addr>}

Description

This command shows information for an Air Monitor’s current status, message counters, or profile settings.

Parameter	Description
counters	Shows the maximum classification delay that was observed in monitored APs and clients, the number of Unclassified Device messages that were sent to the WMS, and the number of monitored APs/clients that were present in those messages. This parameter also shows the number of monitored APs/clients that were created and removed by the AP. This information is captured on an hourly basis for the last 24 hours. NOTE: The maximum delay for clients is not displayed if the `unclass_sta_update` parameter is not enabled.
profile-config	Shows the configuration received by the AP for each profile.
status	Shows general AP status information and the maximum classification delay that was observed in monitored APs and clients, in the WLAN Interface option. NOTE: The maximum delay for clients is not displayed if the `unclass_sta_update` parameter is not enabled.
ap-name <ap-name>	Show data for an AM with a specific name.
bssid <bssid>	Show data for an AM with a specific BSSID. The BSSID is usually the AP’s MAC address.
ip-addr <ip-addr>	Show data for an AM with a specific IP address by entering its IPv4 address in dotted-decimal format.
ip6-addr <ip6-addr>	Show data for an AM with a specific IP address by entering its IPv6 address in dotted-decimal format.
am-scan	Show Air Monitor active scanning configuration.
ap-radio	Show the Air Monitor radio configuration parameters, as defined in the AM’s 802.11a, 802.11b, or high-throughput radio profiles.
ap-system	Show an Air Monitor’s system configuration settings, as defined in it’s AP System profile.
arm	Show an Air Monitor’s ARM settings, as defined in its current ARM profile
event-thresholds	Show an Air Monitor Event Thresholds settings, as defined in its current RF Event Thresholds profile
ids-dos	Show an Air Monitor IDS DoS settings, as defined in its current IDS DoS profile.
ids-general	Show an Air Monitor IDS General Configuration settings, as defined in its IDS General profile.
ids-impersonation	Show an Air Monitor IDS Impersonation Configuration settings, as defined in its IDS Impersonation profile.
ids-signature-matching	Show an Air Monitor IDS Signature Matching configuration settings, as defined in its IDS Signature Matching profile
ids-unauthorized-device	Show an Air Monitor IDS Unauthorized Device configuration settings, as defined in its IDS Unauthorized Device profile.
interference	Show an Air Monitor’s interference configuration settings, as defined in its current RF Optimization profile.
regulatory-domain	Show an Air Monitor’s Regulatory Domain configuration settings, as defined in its Regulatory Domain profile.
rf-behavior	Show an Air Monitor RF Behavior Configuration

Examples

The output of the following command includes the WLAN Interface, Data Structures, WLAN InterfaceSwitch Status and RTLS Configuration tables for the specified AP.

(host) #show ap monitor debug status ap-name ap12

WLAN Interface

--------------

bssid scan monitor probe-type phy-type task channel pkts

----- ---- ------- ---------- -------- ---- ------- ----

00:1a:1e:11:5f:10 enable enable sap 80211a-HT-40 tuned 153 496970814

00:1a:1e:11:5f:00 enable enable airmatch-am 80211b/g-HT-20 tuned 6 391278179

Wired Interface

---------------

mac ip gw-ip gw-mac status pkts

--- -- ----- ------ ------ ----

macs gw-macs tagged-pkts vlan

---- ------- ----------- ----

00:1a:1e:c9:15:f0 192.0.2.32.200 192.0.2.32.254 00:0b:86:08:e1:00 enable 101960

2 3 1 03

Global Counters

---------------

key value

--- -----

Packets Read 888248993

Bytes Read 2819670134

Num Interrupts 681037971

Num Buffer Overflows 591393

Max PPS 16239

Cur PPS 1130

Max PPI 20

Cur PPI 2

Uptime 3323085

AP Name AL12

LMS IP 192.0.2.250

Master/Conductor IP 192.0.2.253

AP Type 125

Country Code 2

Starting from AOS 8.4.0.0, the output of the command show ap monitor debug status includes the new counters to differentiate the distribution of DATA, MGMT, CTRL, and AGGR packets.

WLAN packet counters for DATA

------------------------------

Interface Data Pkts Data Bytes Data Max PPS Data Cur PPS Data Max BPS Data Cur BPS

--------- --------- ---------- ------------ ------------ ------------ ------------

18:64:72:7e:51:d0(wifi0) 67730 3045300 366 5 36600 140

18:64:72:7e:51:c0(wifi1) 0 0 0 0 0 0

WLAN packet counters for MGMT

------------------------------

Interface MGMT Pkts MGMT Bytes MGMT Max PPS MGMT Cur PPS MGMT Max BPS MGMT Cur BPS

--------- --------- ---------- ------------ ------------ ------------ ------------

18:64:72:7e:51:d0(wifi0) 2835404 750667644 217 31 60416 8512

18:64:72:7e:51:c0(wifi1) 0 0 0 0 0 0

WLAN packet counters for CTRL

------------------------------

Interface CTRL Pkts CTRL Bytes CTRL Max PPS CTRL Cur PPS CTRL Max BPS CTRL Cur BPS

--------- --------- ---------- ------------ ------------ ------------ ------------

18:64:72:7e:51:d0(wifi0) 5466191 106264680 6910 28 132428 512

18:64:72:7e:51:c0(wifi1) 0 0 0 0 0 0

WLAN packet counters for AGGR

------------------------------

Interface FIRST AGGR MIDDLE AGGR LAST AGGR TOTAL AGGR NUM NON AGGR

--------- ---------- ----------- --------- ---------- ------------

84:d4:7e:d1:d7:d0(wifi0) 4059 3452 4147 11658 95687

84:d4:7e:d1:d7:c0(wifi1) 0 0 0 0 0

Data Structures

----------------

ap sta pap psta ch msg-hash ap-l

-- --- --- ---- -- -------- ----

20 40 17 55 24 21 20

Other Parameters

-----------------

key value

--- -----

WMS on Master/Conductor disabled

Stats Update Interval 60

Poll Interval 174000

Num Switches 1

Collect Stats enabled

WLAN Interface Switch Status

-----------------------------

Bssid Type Status Last-reg N-reg Last-update Next-update N-updates Last-ack

----- ---- ------ -------- ----- ----------- ----------- --------- --------

00:1a:1e:11:5f:10 local up 3321891 3821 3322965 197 10368 3322965

00:1a:1e:11:5f:00 local up 3321891 3821 3322917 187 10378 3322965

RTLS Configuration and State

-----------------------------

Type Server IP Port Freq Active Rpt-Tags Tag-Mcast-Addr

---- --------- ---- ---- ------ -------- --------------

MMS N/A N/A N/A disable 01:0c:cc:00:00:00

Aeroscout 2001::3 N/A 30 * disable 00:00:00:00:00:00

RTLS 2001::2 N/A 20 * disable 01:18:8e:00:00:00

Tags-Sent Rpt-Sta Incl-Unassoc-Sta Sta-Sent Cmpd-Msgs-Sent

--------- ------- ---------------- -------- --------------

N/A disable N/A N/A N/A

N/A enable disable 2610 265

N/A enable enable

The output of this command includes the following parameters:

Column	Description
bssid	BSSID for the AP. This is usually the AP’s MAC address.
scan	Indicates whether or not if active scanning is enabled on this AP.
monitor	Indicates whether the AP radio is currently enabled or disabled.
probe-type	This parameter displays one of the following options to show the AP is configured. sap: Default AP setting. am: AP is configured as an Air Monitor. m-portal: AP is configured as a Mesh portal. m-point: AP is configured as a Mesh point. airmatch-am: AP is configured in AP monitoring mode.
task	This parameter displays one of the following options to show the radio’s current task: scan: AP is scanning other channels. tuned: AP is tuned on one channel. locate: AP has been asked to locate a specific AP or client. pcap: The AP is enabled with the Packet Capture feature.
channel	The radio channel currently used by an AP’s WLAN interface.
pkts	Number of packets seen on the interface.
mac	MAC address for the AP’s wired interface.
ip	The AP’s IP address.
gw-ip	IP address for the AP’s gateway.
gw-mac	MAC address for the AP’s gateway.
status	Shows if the interface is currently enabled or disabled.
pkts	Number of packets seen on the AP’s wired interface.
macs	Number of MAC addresses in the Wired MAC table for that interface.
gw-macs	Number of MAC addresses in the Wired MAC table for that interface.
tagged-pkts	Number VLAN-tagged packets sent to that interface.
vlan	The VLAN ID for the packets sent to that interface.
Packets read	Number of packets read by the AP since it was last reset.
Bytes read	Number of bytes read by the AP since it was last reset.
Num Intercepts	Number of interrupts from the AP’s driver.
Num Buffer Overflows	Number of times excessive traffic has filled the AP’s buffers.
Max PPS	Maximum throughput rate seen on the interface, in packets per second.
Cur PPS	Current throughput rate seen on the interface, in packets per second.
Max PPI	Maximum interrupt rate seen on the interface, in interrupts per second.
Cur PPI	Current interrupt rate seen on the interface, in interrupts per second.
Uptime	Number of seconds since the AP was last reset.
LMS IP	IP address of the AP’s managed device
Master/Conductor IP	IP address of the AP’s Mobility Conductor.
AP type	AP model type.
Country Code	The AP’s country code. Valid radio channels for your wireless network are based on your country code. If you change the AP’s country code, the valid channels will be reset to the defaults for the new country.
ap	Number of other APs monitored by this AP.
sta	Number of clients and APs seen by this AP.
pap	Number of potential APs; APs which have transmitted a beacon, but have not yet been registered.
psta	Number of potential stations; AP has seen a MAC address from the station but hasn’t yet received traffic from it.
ch	Number of channel entries in the channel table.
msg-hash	Number of different message types seen on the interface.
ap-l	(For internal use only)
WMS on Master/Conductor	Indicates if the AP communicates to the wms process on Mobility Conductor or a managed device. enabled: Communicates with Mobility Conductor. disabled: Communicates with a managed device only.
Stats Update Interval	If the AP is collecting statistics, this value is the interval in seconds in which the AP sends statistics to the WMS process.
Poll Interval	Interval, in milliseconds, that the AP sends RSSI updates to the WMS process.
Num Switches	Number of controllers to which this AP has access. If the value is 1, the AP has access to Mobility Conductor or a managed device. If the value is 2, the AP has access to Mobility Conductor and a managed device.
Collect Stats	If enabled, the AP will collect statistics to send to the WMS process.
Bssid	BSSID of the radio.
Type	Indicates whether the controller type is master (Mobility Conductor) or local (managed device).
Status	If up, the AP can reach the managed device. If down, the AP cannot reach the managed device.
Last-reg	The time the AP last registered with the WMS process.
N-reg	Number of times the AP has registered with the WMS process.
Last-update	The last timer tick time the AP updated the WMS process.
Next-update	Interval between the last update and the next scheduled update.
N-updates	Number of updates sent to the WMS process.
Last-ack	Number of timer ticks since the AP received an acknowledgment from the WMS process.
Type	Type of RTLS server used by the AP, such as MMS or Aeroscout.
Server IP	IP address of the RTLS server.
Port	Port used by the RTLS server.
Frequency	Rate, in seconds, at which RTLS messages are sent to the server.
Active	Indicates if the server is active on the AP.
Rpt-Tags	Displays whether tag reporting is enabled or not.
Tag-Mcast-Addr	Displays MAC OUI of the tags that are forwarded to the server.
Tags-Sent	Displays the cumulative count of the tag reports sent to server.
Rpt-Sta	Displays whether station reporting is enabled or not.
Incl-Unassoc-Sta	Displays whether unassociated stations are included in station reporting or not.
Sta-Sent	Displays cumulative count of station reports sent to server.
Cmpd-Msgs-Sent	Displays cumulative count of compound messages containing station reports sent to server.

Starting from AOS 8.11.0.0, the output of the show ap monitor debug status command includes new counters that list discarded and detected Apple Wireless Direct Link (AWDL) frames.

AM AWDL Counters (wifi0)

-------------------------

Parameter Value

--------- -----

Dropped AWDL frames 0

Detected AWDL frames 1171

The output of this command includes the following parameters:

Column	Description
Parameter	Type of Apple Wireless Direct Link frame.
Value	Number of Apple Wireless Direct Link frames that are dropped or detected.

Related Command

Command	Description
show ap monitor	This command shows information for HPE Aruba Networking Air Monitors.

Command History

Release	Modification
AOS 8.11.0.0	The following modifications were introduced: The output of the `show ap monitor debug status` command includes new counters that list detected and discarded Apple Wireless Direct Link frames. The output of the show ap monitor debug profile-config command includes the details of containment exclusion.
AOS 8.10.0.0	The probe type airmatch-am was introduced in the output of the command under WLAN Interface table.
AOS8.9.0.0	The output was modified to include the following changes: Replaced `phy-type` with `band/chan/ch-width/ht-type`. Replaced `802.11g` and `802.11a` with `2.4GHz` and `5GHz`. Introduced `6GHz` parameter for Wi-Fi 6E APs. All instances of `master` have been replaced with `conductor`.
AOS 8.8.0.0	The output was modified to include zero wait DFS channel details.
AOS 8.4.0.0	The following changes were introduced: The `ip6-addr` parameter was added. The output of the `show ap monitor debug status` command displays both IPv4 and IPv6 addresses. The output of the `show ap monitor debug status` command includes new counters to differentiate the distribution of DATA, MGMT, CTRL, and AGGR packets.
AOS 8.0.0.0	Command introduced.

Command Information

Platforms	License	Command Mode
All platforms	Base operating system.	Enable or Config mode on Mobility Conductor.