ISO and Aruba Central On-Premises Software Installation

The ISO installation can be performed only on Central-ready appliances.

Aruba Central On-Premises installation is a 3-stage process with multiple options in each stage:

  1. Install Aruba Central On-Premises ISO on the Server
  2. Install Aruba Central On-Premises Apps Short form for application. It generally refers to the application that is downloaded and used on mobile devices. Package on the Server

    The Apps package is uploaded on an SCP Secure Copy Protocol. SCP is a network protocol that supports file transfers between hosts on a network. server reachable to the Aruba Central On-Premises node IP address.

  3. Setting up a Cluster
    • Assign permanent IP address and network settings to all the nodes.
    • Cluster setup with all nodes.
    • Proceed with Step 1 and Step 2 for the nodes that are part of Aruba Central On-Premises cluster already.

Installing Aruba Central On-Premises ISO Files on Central-Ready Airwave Appliance

There are 2 ways to install Aruba Central ISO to the Central Appliance:

  • Using the iLO interface with ISO image on the PC or Desktop
  • Using the ISO image on an HTTPS server

Installing Aruba Central On-Premises ISO Files Using the iLO interface with ISO image on the PC

  1. Obtain the iLO IP address assigned statically or by DHCP Dynamic Host Configuration Protocol. A network protocol that enables a server to automatically assign an IP address to an IP-enabled device from a defined range of numbers configured for a given network. .
  2. Log into iLO IP address using the username and password on top of the server.
  3. On the iLO's Overview page, you can see that the appliance has Trusted Platform Module (TPM Trusted Platform Module. TPM is an international standard for a secure cryptoprocessor, which is a dedicated microcontroller designed to secure hardware by integrating cryptographic keys into devices.) enabled. If the option is not present or not enabled, Aruba Central software cannot be installed on the server.
  4. The iLO Firmware version is 2.55, which is required for Aruba Central 2.5.5 version. However, on older appliance, the iLO Firmware may be 1.40 or lower versions. Post ISO installation, the Aruba Central software will update the iLO Firmware too.

    Figure 1  iLO Overview Page

  5. Set the Boot process to CD/DVD Drive from Administration > Boot order. Use the Up or Down button to move the CD/DVD Drive and click Apply.

    Figure 2  iLO Boot Order Page

  6. Download the ISO image to the computer.
  7. Connect to the Java Web Console or HTML console on the iLO.
  8. Select the Disc icon > CD/DVD > Local *.iso file.
  9. Browse and select the ISO file from the computer and the ISO file is mounted to the server.

    Figure 3  iLO Java Console Page

  10. Reboot using the iLO icon > Power > Reset. The server boots up with ISO image and installs the Aruba Central OS.

    Figure 4  iLO Power Page

  11. Reboot post the installation and proceed to Central Apps package installation. For more information, see Installing Central Apps (Package Installation).

For information about the boot process and iLO upgrade, see Aruba Central On-Premises Installation Guide-Technotes.

Installing Aruba Central On-Premises ISO Files Using the ISO image on an HTTPS server

  1. Get the iLO IP address assigned statically or by DHCP.
  2. Log Into iLO IP using the username and password on top of the server.
  3. Set the Boot process to CD/DVD Drive from Administration > Boot order. Click the Up and Down button to move the CD/DVD Drive to top and click Apply.

    Figure 5  iLO Boot Order Page

  4. Download the ISO image to an HTTPS server accessible from iLO IP address.
  5. Connect to the Java Web Console or HTML.
  6. Select Virtual Drives > URL CD/DVD-ROM.

    Figure 6  iLO Virtual Drives Options

  7. Copy paste the HTTPS link for the ISO image.

    Figure 7  Image File at URL Page

  8. After the file is attached, reboot the server from Power Switch > Reset option. The server after the initial boot process should boot from the CD-ROM. The ISO installation takes about 25 minutes when using a bootable disk. If you are using ILO, the time depends on the network speed and VPN Virtual Private Network. VPN enables secure access to a corporate network when located remotely. It enables a computer to send and receive data across shared or public networks as if it were directly connected to the private network, while benefiting from the functionality, security, and management policies of the private network. This is done by establishing a virtual point-to-point connection through the use of dedicated connections, encryption, or a combination of the two. connection, if used remotely either from PC or using HTTPS server.

For more information on the boot process, see Aruba Central On-Premises Installation Guide-Technotes.

Installing Central Apps (Package Installation)

At the time of installing the Central apps (Package Installation), the BIOS and GRUB passwords are changed automatically. Contact the Aruba Central support team to know more on BIOS and GRUB access.

Setting Up Temporary Network

The following information helps you perform the steps to set up the temporary network after completing the ISO installation specific to Aruba Central.

Pre-requisites

Ensure that the following actions are complete before setting up the temporary network:

  • The Aruba Central ISO installation is completed on Central-ready appliance.
  • The HPE ProLiant server is manually rebooted.

Perform the following steps to set up a temporary network:

  1. Login to HPE ProLiant server using the following default credentials:
  2. Enter 4 to select the System Configuration option and go to the next menu item.

    Figure 9  CLI Main Menu Page

  3. Enter 2 to select the Network Setup option and go to the next menu item.

    Figure 10  CLI Network Setup Page

  4. Enter 2 to select the Temporary Network Settings option and go to the next menu item.

    Figure 11  CLI Temporary Network Page

  5. When prompted, enter the following network settings to set up the temporary network:

Enter M to go back to the main menu.

Uploading Aruba Central Apps Tarball

Perform the following steps to upload the Aruba Central apps tarball:

  1. In the Aruba Central CLI, enter 2 to upload the tarball file and go to the next menu item.

    Figure 12  CLI Main Menu Page

  2. Enter the details of apps tarball that are required to be copied from remote server via SCP.

    The SCP progress related to apps tarball is displayed on the console.

  3. Enter 5 followed by 2 to confirm that the apps tarball has been uploaded.

Installing COP Software

  1. In the Aruba Central CLI, enter 6 to select the Install COP Software option.

    Figure 13  CLI Main Menu Page

    A list of available tarball file candidates is displayed.

  2. Enter the number corresponding to the tarball file that is displayed in the list.
  3. Wait for the software installation to completion.
  4. Once the ISO and Aruba Central On-Premises software installations are complete, you can set up the network cluster. For more information, see .