Switch Events

Informational Events

Fan module {FMod_Name} was removed.

Fan module {FMod_Name} was inserted.

Status of fan {FanName} has changed from {OldStatus} to {NewStatus}

Fan tray {FT_Name} powered {Status}

PSU {name} changed state to {state}

Interface {interface} encountered a hardware error that caused a link reset.

Interface {interface} downshifted to speed {port_speed} Mbps because link attempt failed at higher speed.

Sensor {name} back to safe temperature, {temp} degC.

Ambient temperature for sensor {name} back to safe temperature, between {t_low} and {t_high} degC.

NTP Association {event} : {server} {server_info}.

NTP Trusted keys {trusted_keys} and Untrusted keys {untrusted_keys}.

NTP Authentication state change : {old} -> {new}.

NTP VRF state change : {old} -> {new}.

NTP primary server connection established to {server}.

NTP primary server connection lost to {server}.

NTP enable state change : {old} -> {new}.

Interface {intf_name} cannot be part of Lag {lag_number}. Speed mismatched (Interface speed {port_speed}Mbps Lag base speed {lag_speed}Mbps)

{proto} - Root changed from {old_priority}: {old_mac} to {new_priority}: {new_mac}

BPDU loss- port {port} moved to inconsistent state for {proto}

Port {port} moved out of inconsistent state for {proto}

Topology Change received on port {port} for {proto} from source: {mac}

{proto} - Topology Change generated on port {port} going in to {state}

BPDU received on admin edge port {port}

This log event informs the user that the CIST port is blocked.

Port {port} unblocked on CIST

Port {port} blocked on MST{instance}

Port {port} unblocked on MST{instance}

{proto} Root Port changed from {old_port} to {new_port}

spanning tree mode changed from {old_mode} to {new_mode}, it will trigger the reconvergence

Failover detected: Reason {reason}

Lost {mgmt_module} as Standby Management Module, redundancy disabled

Detected the removal of the Standby Management Module

{mgmt_module} is Active

{mgmt_module} is Standby

Detected {mgmt_module} as Standby Management Module, redundancy enabled

Remote Standby Management module recover detected. Reason: Heartbeat loss

{mgmt_module} is waiting for filesync

{mgmt_module} is starting ISSU operation

AdjChg: Nbr {router-id} on {ospf-interface}({area}): {old_state} -> {new_state}

Interface {interface}({area}) changed from {old_state} to {new_state}, input: {input}

{event} with {destination} {nexthops}

AdjChg: Nbr {router-id} on {ospf-interface}: {state} -> {next_state} ({event})

Router-id updated from {old} to {new}

Port {portName} enabled after disable time expired

Port {portName} added for loop-protection

Port {portName} deleted from loop-protection

Loop-Protection stats cleared for port {portName}

Ports TX {txportName} and RX {rxportName} are involved during TX port disabling

{remote-addr}: Peer up. vrf-name: {vrf-name}

{remote-addr}: Peer down. error-code: {error-code}, error-sub-code: {error-subcode}. vrf-name: {vrf-name}

{remote-addr}: Peer has received prefix equal to Maximum Prefix value configured. vrf-name: {vrf-name}

{remote-addr}: Peer has received prefix equal to Threshold value configured. vrf-name: {vrf-name}

BGP AS {as_number} configured. vrf-name: {vrf-name}

BGP AS {as_number} unconfigured. vrf-name: {vrf-name}

BGP router-id changed: {ip} vrf-name: {vrf-name}

{remote_addr}: Peer configured, AS {remote_as}. vrf-name: {vrf-name}

{remote_addr}: User reset request. vrf-name: {vrf-name}

{remote_addr}: Peer password changed. vrf-name: {vrf-name}

{remote_addr}: Peer deleted. vrf-name: {vrf-name}

{remote_addr}: Peer admin disabled. vrf-name: {vrf-name}

{remote_addr}: Peer admin enabled. vrf-name: {vrf-name}

{remote_addr}: Peer remote-as changed to {remote_as}. vrf-name: {vrf-name}

{remote_addr}: Peer local-as changed to {local_as}. vrf-name: {vrf-name}

{remote_addr}: Peer source-address changed to {src_ipaddr}. vrf-name: {vrf-name}

{remote_addr}: Peer remove-private-as configuration changed. vrf-name: {vrf-name}

{bgp_id}: BGP identifier sent by Peer {remote_addr} matches ours. BGP session may not established. vrf-name: {vrf-name}

{pg_name}: Peer-group configured with remote-as {remote_as}. vrf-name: {vrf-name}

{remote_addr}: Peer ignore-leading-as configuration changed. vrf-name: {vrf-name}

{type} module {name} is ready

{type} module {name} is down: {reason}

{type} module {name} admin state set to up

{type} module {name} admin state set to down

{type} module {name} configured with product number {part_number}

{type} module {name} has been unconfigured

allow-unsupported-transceiver feature enabled

allow-unsupported-transceiver feature disabled

allow-unsupported-transceiver feature enabled: Unsupported transceivers found in: {list}

Transceiver hot-swap insert for interface {interface}

Transceiver hot-swap remove for interface {interface}

Transceiver {xcvr_desc} inserted in {interface} is {status}. {reason}

OSPF3 all routers field entry added: group_id={group_id} fp_id={fp_id} stat_id={stats_id}

OSPF3 designated routers field entry added: group_id={group_id} fp_id={fp_id} stat_id={stats_id}

AdjChg: Nbr{router-id} on interface {link-local} on {interface}({area}): {old_state} -> {new_state}

Interface {link-local} on {interface}({area}) changed from {old_state} to {new_state}, input: {input}

Graceful Restart state changed, {old_state} -> {new_state}, reason: {reason}

Distance External {external}, Inter-area {inter}, and Intra-area {intra} applied to OSPFv3 process {process-id} in {vrf} VRF

RPVST Enabled

RPVST Disabled

RPVST - Root changed from {old_priority}: {old_mac} to {new_priority}: {new_mac} on VLAN {vlan}.

Topology change received on port {port} from source: {mac} on VLAN {vlan}.

Topology change generated on port {port} on VLAN {vlan}.

Root port changed from {old_port} to {new_port} on VLAN {vlan}.

PVID mismatch detected on {interface} with pvid = {pvid}, Neighbor pvid = {npvid}

spanning tree mode changed from {old_mode} to {new_mode}, it will trigger the reconvergence

Current Virtual Ports {Current_Virtual_Ports} exceeds the max supported limit {Maximum_Virtual_Ports}

VSX ISL port {port} is down

VSX ISL port {port} is up

VSX ISL port {port} is In-Sync with the peer.

VSX Keepalive succeeded

VSX role is primary

VSX role is secondary

VSX Software version mismatch: peer version {peer_sw_ver}, local version {local_sw_ver}

VSX Device mismatch: peer device {peer_device_type}, local device {local_device_type}

VSX {vsx_id} state local up, remote down

VSX {vsx_id} state local down, remote up

VSX {vsx_id} state local up, remote up

VSX {vsx_id} state local down, remote down

VSX ISL sliding window parameters are reset.

VSX own ISL hello packet received, ignoring the packet.

ISL out-of-sync and keepalive is in established

ISL out-of-sync and keepalive also failed

Linkup delay timer started

Linkup delay timer expired

VSX {vsx_role} state changed from {prev_state} to {state}.

Bailout timer started

Bailout timer expired

Bailout timer stopped

Linkup-delay timer stopped

VSX device roles are inconsistent: local VSX device role {local_vsx_role}, peer VSX device role {peer_vsx_role}

VSX Keepalive is configured without creating VRF

VSX Keepalive is configured without configuring IP address

Netdev {ifname} configured with ipv4 address {value}

Netdev {ifname} configured with ipv6 address {value}

IP-SLA session:{name} state changed to {state} due to reason {reason}

IP-SLA {name}: {operation}

PoE usage exceeded threshold limit of {threshold_limit}

PoE controller {cntrl_name} got into fault

PoE controller {cntrl_name} got reset

Powered device is drawing power more than its class on interface {interface_name}, type:{pd_type} class:{pd_class} power:{power} is exceeding the max average power of the PD class. Check the PD max power draw, cabling type and length to improve interoperability

Powered device UVLO fault on interface {interface_name}, will attempt to recover itself by toggling power

Powered device FET BAD fault on interface {interface_name}

Powered device disconnected on interface {interface_name} due to pd-class-override config change

Powered device disconnected on interface {interface_name} due to power-pairs config change

PoE usage is below threshold of {threshold_limit}

Vtep-Peer {vtep_peer} is created

Vtep-Peer {vtep_peer} has been deleted

Vtep-Peer {vtep} state is configuration_error

Vtep-Peer {vtep} state is no_hw_resources

Client {mac} on vlan {vid}, port {port} received {client_ip} from server {server_ip} with lease {lease}. Nameserver:{nameserver_ip}.

Client {mac} on vlan {vid}, port {port} released {client_ip}.

Client {mac} on vlan {vid}, port {port} lease period expired for {client_ip}.

Client {mac} on vlan {vid}, port {port} with {client_ip}. Client attributes updated: Nameserver {nameserver_ip}, Lease period {lease}.

Client {mac} on vlan {vid}, port {port} received {client_ip} from server {server_ip} with lease {lease}. Nameserver:{nameserver_ip}, Gateway:{gateway_ip}.

Client {mac} on vlan {vid}, port {port} released {client_ip}.

Client {mac} on vlan {vid}, port {port} lease period expired for {client_ip}.

Client {mac} on vlan {vid}, port {port} with {client_ip}. Client attributes updated: Gateway {gateway_ip}, Nameserver {nameserver_ip}, Lease period {lease}.

Member {member_id} boot complete

Standby {member_id} boot complete

Conductor {member_id} boot complete

Resetting member {member_id}

Topology is {topo_type}

Member {member_id} removed

Stack state is no-split with conductor id {member_id}

Reboot of MAC {mac_address} status-{status}

Member {member_id} elected as conductor reason-{reason}

Member {member_id} elected as standby reason-{reason}

VSF link {link} is up

VSF link {link} is down

Invalid MAC {mac_address} detected on link {link} with peer MAC {mac_add}

2 member loop detected on ring topology

Fragment with conductor {member_id} is Active

Fragment with conductor {member_id} is Inactive

Active fragment detection timeout

Member {member_id} is configured as Secondary

Secondary configuration removed

Attempt to connect a member with MAC {mac_address} and product type {product_id} having different airflows

Interface {port_id} added to VSF link {link}

Interface {port_id} removed from VSF link {link}

VSF force autojoin enabled

VSF force autojoin disabled

Secondary member changed from {old_standby_id} to {new_standby_id}

Client with MAC address {mac_addr} learnt on port {if_name}.

Client with MAC address {mac_addr} deleted on port {if_name}.

Client with MAC address {mac_addr} authorized on port {if_name} with role {role_name}.

Client with MAC address {mac_addr} on {if_name} failed {auth_method} authentication with reason {failure_reason}.

Client with MAC address {mac_addr} on port {if_name} triggered for MAC-Authentication request with ID {request_id}.

Client with MAC address {mac_addr} on port {if_name} received response for MAC-Authentication request ID {request_id} as {response}.

Client with MAC address {mac_addr} on port {if_name} triggered for 802.1x authentication request with ID {request_id}.

Client with MAC address {mac_addr} on port {if_name} received response for 802.1x authentication request ID {request_id} as {response}.

Client {mac_address} was logged-off administratively through command-line interface

Clients were logged-off on the port {port} due to a change in authentication mode from {old_mode} to {new_mode}

Clients were logged-off on the port {port} due to a change in client limit from {old_limit} to {new_limit}

Clients using policy {policy_name} were logged-off due to a configuration change in the policy

Client limit exceeded on port {port}, caused by an unauthenticated client {mac_addr}

All clients except client with MAC address {mac_addr} logged-off on the port {port} due to a change in authentication mode from {old_mode} to {new_mode}

All clients except client with MAC address {mac_addr} logged-off on the port {port} due to proxy-logoff request

MAC Lockout packet drop detected for {mac} as source address with packet count: {sa_diff_count}.

MAC Lockout packet drop detected for {mac} as destination address with packet count: {da_diff_count}.

MAC Lockout packet drop detected for {mac} as source & destination address with source packet count: {sa_diff_count} and destination packet count: {da_diff_count}.

HW Fault (Error {error_code}) detected on the switch. {impact_statement}. Contact support for assistance.

Client {mac} successfully on-boarded on VLAN {vlans}. Client on-boarding started at {ob_start_ts}; L2 complete at {l2_end_ts}; L3 complete at {l3_end_ts}

Client {mac} partial success while on-boarding on VLAN {vlans}. L2 status:{l2_ob_state} L3 status:{l3_ob_state}. Client on-boarding started at {ob_start_ts};L2 complete at {l2_end_ts}; L3 complete at {l3_end_ts}.

Client {mac} failed to on-board with status: {onboarding_status} reason_code: {failure_phase_id}

Client {mac} successfully on-boarded on VLAN {vlans}; Client on-boarding started at {ob_start_ts}; L2 complete at {l2_end_ts}; L3 complete at {l3_end_ts}; ARP to GW response received at {arp_end_ts}; DNS on-boarding to {dns_server_ip} completed at {dns_end_ts}

Client {mac} on-boarded on VLANs {vlans} and failed on VLANs {failed_vlans}; Client on-boarding started at {ob_start_ts}; L2 complete at {l2_end_ts}; L3 complete at {l3_end_ts}; ARP to GW response received at {arp_end_ts}; DNS on-boarding to {dns_server_ip} completed at {dns_end_ts}; L2 status {l2_ob_state} failure_reason_code - {l2_failure_reason}; L3 status {l3_ob_state} failure_reason_code - {l3_failure_reason}; DNS on-boarding status {dns_status} failure_reason_code - {dns_failure_reason}

Client {mac} failed to on-board with status: {onboarding_status} in failure phase: {failure_phase_id} with reason: {failure_reason}

Critical Events

{process} crashed due to {signal},{timestamp}

The BGP RIB has reached the threshold limit of {threshold_limit} for VRF {vrf-name}

MGMT_INTF: {mgmt_intf_config_crit}

Conflict in authorization configuration. Existing config::URL({match}), type({value}) New config::({url}), type({autztype})

{msg}

QoS failed final initialization on new slot {new_slot} for peer slot {existing_slot}

Update failed for {devspec}

Failed to write-protect {devspec} (pass {pass})

ZTP service status changed to failed because of invalid configuration file.

ZTP service status changed to failed because of invalid image file.

ZTP service status changed to failed because {filename} file download encountered unexpected error.

ZTP service status changed to failed because {filename} file did not get downloaded.

ZTP service status changed to failed because the downloaded configuration could not be copied to start-up configuration.

Tunnel Node Server UAC node is down ({uac_ip})

IP source-lockdown resource utilization has exceeded maximum supported limit of {max_supported_limit} on the system. IP source-lockdown functionality will not work for new entries.

Line card module {linecard_name} triggered backplane enhanced sequence recovery.

Emergency Events

Shutting down system now because {num_of_failure} {failure_type} {compare_mode} limit of {num_of_failure_limit}

Available system memory is critically low

Unable to get current system memory usage

Available system memory is critically low. Reboot will be triggered soon.

{process} exiting. Reason: {reason}

{msg}

The FIPS POST service has reported a self-test failure.

Jitter Entropy has reported a self-test failure.

The cryptographic self-test monitor has detected a reported test failure. The self-test mode has been configured to fail-secure. The switch will be rebooted.

Warning Events

Operational fan count below minimum. {FanCount} fans operating, but {FanMinimum} are required.

PSUs inserted in the system are of {Type} types. This is {Support} configuration.

PSU {name}: Internal communication {status}

PSU {name}: Fan-{fanidx} {status}

PSU {name}: {sensorid} sensor {status} threshold limit

PSU {name}: Output current {status} threshold limit

'{type} module {name} denied power due to insufficient power. Configured PoE power can be deconfigured to allow card to be granted power.

PSU {name} disabled: PSU inserted is not supported by the system.

Invalid PoE power configuration, using default maximum PoE power.

Interface {interface} is down because MACsec and PFC features are mutually exclusive.

Interface {interface} cannot be enabled due to invalid configuration.

Interface {interface} split unsupported in profile {profile}.

Unrecognized sensor type {type}

Module {module} shutdown initiated for sensor {name} with critical temperature, {temp} degC.

Over-temperature for sensor {name}, {temp} degC

Ambient temperature for sensor {name} above {temp} degC

Ambient temperature {temp} degC is above the commercial grade transceiver limit of {limit_high} degC

Ambient temperature {temp} degC is below the commercial grade transceiver range of {limit_low} degC

Ambient temperature for sensor {name} below {temp} degC

Under-temperature for sensor {name}, {temp} degC.

Module {module} shutdown initiated for sensor {name} with low critical temperature, {temp} degC.

Available system memory is back to normal state

Memory reservation for reboot library failed.

The {log_type} buffer is almost full.

The {log_type} buffer has wrapped, older logs will be overwritten.

Partner is out of sync for interface {intf_id} LAG {lag_id}. Actor state: {actor_state}, partner state {partner_state}

Partner is lost (timed out) for interface {intf_id} LAG {lag_id}. State: {fsm_state}

{config_parameter} should be {value}

BPDU has {config_parameter} from port {value}

Bad reconfiguration request: {reconfig_parameter}

Port {port} disabled - BPDU received on protected port

Received packet from {ip_address}, type {type}, on invalid port {port}

All bitmaps have been allocated.

Over 80 percent of bitmaps have been allocated.

Multicast L3 Bridge Control Forwarding entry with uuid {uuid_str} has no reference to a VLAN

Port {portName} is disabled by Loop-protection after loop detection on VLAN {vlan}

Ports TX {txportName} and RX {rxportName} are disabled by Loop-protect after loop detection on VLAN {vlan}

Loop detected on port {portName} on VLAN {vlan}'

Port {portName} is disabled by Loop-protection after loop detection on VLAN {vlan}

There are {origin} happening on {location}

There are IO errors on {location} from {seg}:{bus}:{device}:{function}

CPUs {cpus} L{level} {type} cache error detected. CPUs {offlined} offlined

Socket {socket} correctable memory error count {cecount} exceeded threshold {threshold}

Page {page} correctable memory error count {cecount} exceeded threshold {threshold} and {offlined}

Diagnostic {test_name} failed with error code {error_code} on management module {slot} and report as warning

Diagnostic {test_name} failed with error code {error_code} on fabric card {slot} and report as warning

Diagnostic {test_name} failed with error code {error_code} on line card {slot} and report as warning

Diagnostic {test_name} failed with error code {error_code} on fan tray {slot} and report as warning

Diagnostic {test_name} failed with error code {error_code} on chassis {slot} and report as warning

{type} module {name} removed

{type} module {name} ISP skipped

{type} module {name} power request has been denied

{type} module {name} disabling front-end power: {reason}

Interface {interface} transceiver attempted link recovery {count} times

Transceiver {xcvr_desc} inserted in {interface} is {status}. {reason}

Unknown transceiver inserted in interface {interface}

Transceiver in {interface} is incompatible with the interface group speed

Adapter {adapter_desc} inserted in {interface} is {status}. {reason}

Interface {interface} transceiver disabled - {disabled_reason}

The Multicast L3 Bridge Control Forwarding entries limit was reached: {limit}

UDLD interface {intf} interval {intvl_a} clamped to {intvl_b}

User {user} password change failed

Unable to add new subscriber. Max number of subscribers has been reached.

Unable to add new subscription. Max number of subscriptions for {subscriber} has been reached.

REST session from {identity} with User {user_name} is rejected because maximum session limit is reached

L2X thread not running. Attempting to recover

L2X thread recovered

MAC-lockout automatically disabled because active-gateway extended-mac was enabled

Port {port} disabled - BPDU received on protected port on VLAN {vlan}.

Port {port} blocked on RPVST {instance}

Port {port} unblocked on RPVST {instance}

The current virtual port count for RPVST AUTO VLAN has exceeded the maximum supported system limit {lvlan}

Failed to add a mroute for s={source}, g={group} on interface {interfaceName} as the configured mroute limits are reached

Failed to add a mroute for s={source}, g={group} on interface {interfaceName} as the configured sources per group limit is reached

{pkt} packet is discarded on interface {ifname}. Reason: {reason}

SSH session from {ip_address} is rejected because maximum number of SSH sessions is reached.

SSH session from user {user_name} closed because maximum number of sessions per user is reached.

SSH session from {ip_address} denied due to host key verification failure.

An empty SSH allow-list has been enabled and all new SSH connections will be denied.

{msg}

The PFC configuration for interface {ifname} exceeds the system limit of {limit} unique combinations and was not applied.

QoS warning: {warning_string}

Port: {port_name} PFC priority {pri} using queue {queue} should not be sharing the queue with other local-priorities

NAE experiencing a spike in data points to process for NAE monitor {monitorName}. NAE will temporarily stop monitoring new data points for {monitorName}.'

Failed to read system memory usage for module {module_num}

Storage utilization for {partition_name} partition is at {utilization}% in module {module_name}

Excessive write to {partition_name} partition in module {module_name} observed. {mem_usage}GB written over past {unit_count} {unit}

Excessive write to swap in module {module_name} observed. {mem_usage}GB written over past {unit_count} {unit}

An internal error occurred while reading the export password and default export password was used instead.

VSX Keepalive failed

Active-gateway extended-mac automatically disabled because mac-lockout was enabled.

The echo function for the BFD session {session_id} will not become active until a global echo source IP address is configured.

BFD echo cannot be enabled on tunnels. interface={intf}

BFD echo is not supported on IPv6 sessions

BFD single-hop is not supported on interface {intf}

BFD session interval override not supported for protocol {from}

BFD session {direction} interval override of {requested_interval} ms is out of bounds for protocol {from}, using {applied_interval} ms instead

Certificate {name} will expire within {days} days

Certificate {name} has not yet reached its start date

Certificate {name} has expired and can no longer be used

Certificate {name} rejected due to verification failure ({error})

Certificate {name} failed OCSP verification ({status}), but was accepted because OCSP enforcement is set to optional.

Certificate {name} is not set for signing purpose

Certificate {name} is invalid or malformed

Certificate {name} rejected due to OCSP verification failure ({error})

Powered device power denied on interface {interface_name}

Powered device fault on interface {interface_name}. Fault type {fault_type}

Dual signature powered device fault on interface {interface_name} pair {pair}. Fault type {fault_type}

Total power drawn: {power_drawn}W by powered device is exceeding the total available PoE power:{power_available}W. Check the PD max power draw, cabling type and length to avoid system crowbar.

Powered device invalid signature indication on interface {interface_name}.

Powered device denied on interface {interface_name} of line module with Quick PoE enabled. Remove device to avoid crowbar on reboot.

Powered device demoted on interface {interface_name} of line module with Quick PoE enabled. Remove device to avoid crowbar on reboot.

PoE disable ignored on interface {interface_name} because Quick PoE is enabled

Powered device requested power down on interface {interface_name} {duration}

Bluetooth unable to trust pairing device

Bluetooth device rejected because another device is already connected

Server {ip_address} packet received on untrusted port {port} dropped.

Client packet destined to untrusted port {port} dropped.

Packet received from unauthorized server {ip_address} on port {port}.

Received untrusted relay info from client {mac} on port {port}.

Client address {client_mac} not equal to source MAC {source_mac} detected on port {port}.

Binding for {ip_address}:{mac} exists on port {existing_port}. Dropping release request received for the binding on {new_port}.

The dynamic binding for {mac} on port {port} was replaced with a manual binding.

Drop request from {mac} for already assigned address {ip_address}.

Drop offer from {server_ip_address} of already assigned address {lease_ip_address} to {mac}.

Drop offer from {server_ip_address} of {lease_ip_address} address is illegal.

Maximum bindings limit reached on port {port}, dropping request from {mac}.

Flash-storage is active for DHCPv4-Snooping.

Server {ipv6_address} packet received on untrusted port {port} dropped.

Client packet destined to untrusted port {port} dropped.

Packet received from unauthorized server {ipv6_address} on port {port}.

Received untrusted relay info from client {mac} on port {port}.

Binding for {ipv6_address}:{mac} exists on port {existing_port}. Dropping release request received for the binding on {new_port}.

The dynamic binding for {mac} on port {port} was replaced with a manual binding.

Drop request from {mac} for already assigned address {ipv6_address}.

Maximum bindings limit reached on port {port}, dropping request from {mac}.

Flash-storage is active for DHCPv6-Snooping.

Expected R-APS packets not received on {ifID} in ring {ringID} with control VLAN {ccvlan}

Misconfiguration detected on ring {ringID} with control VLAN {ccvlan}. Another node in the ring with mac {node} is also operating as an RPL owner.

Failed to add SA Cache entry: S={src_ip}, G={grp_ip}, R={rp_ip} for Peer {peer_ip} as MSDP SA Cache Limit is reached

ZTP service status changed to failed because TFTP info is not available.

ZTP service status changed to failed because TFTP server is not reachable.

ZTP service status changed to failed because of timeout

PFC TLV status priority mismatch on interface {intf_name}

A local user role with name {role_name} already exists and conflicts with the newly inserted ClearPass role.

A ClearPass role with name {role_name} already exists and conflicts with the newly inserted {role_type} role.

Operational state of {zone} zone is DOWN due to {reason}.

IP source-lockdown resource utilization has reached 80 percent of the supported limit of {max_supported_limit} on the system.

Member {member_id} conflict detected on link {link}

Incompatible version detected

Maximum number of switches in the stack has reached. Cannot add MAC {mac_address} product type {type}

Lost member {member_id} with {reason}

Switch with MAC {mac_address} cannot join stack due to incorrect product id {product_id}

Found Unsupported switch with MAC {mac_address} and Product type {product_type}, connected to switch with MAC {mac_addr} on stack port {port_id}

Heart beat lost for member {member_id}

OS version mismatch detected for member {member_id}

Attempt to connect member {member_id} from a different stack

Invalid MAC {mac_address} detected on link {link} with peer MAC {mac_add}

2 member loop detected on ring topology

Peer timeout on interface {port_id}

Loop detected on interface {port_id}

Switch with mac {mac_address} not able to autojoin as it is connected on interface {port} which is a non default autojoin VSF interface

Switch with MAC {mac_address} not able to autojoin as it is connected to interface {port} which is not provisioned on the conductor for member {member_id}

Switch with MAC {mac_address} is not autojoin eligible

Switch with MAC {mac_address} attempting to autojoin via multiple interfaces

Switch with MAC {mac_address} failed to autojoin as there is no free member number available

Switch with mac {mac_address} failed to autojoin on link {link}, port {port}

Switch has VSF configurations present. Force autojoin will not take into effect. Remove all VSF configurations followed by unconfiguring and reconfiguring force autojoin for it to take into effect

Switch with MAC {mac_addr1} failed to autojoin. Connect the device {mac_addr2} to member {mbr_id} link {link_id} to proceed

Interface {port_id} in VSF link {link} detected a peer with inconsistent VSF link configuration

Switch with MAC {mac_addr} failed to autojoin as it is connected on interface {port_id} which has MACsec configuration

Bringing down MACsec configured interface {port_id} as it is added to a VSF link. VSF link and MACsec configurations needs to be removed from the interface {port_id} and VSF link needs to be reconfigured for it to take into effect

ISSU state failed for member {id} during ISSU operation: "{operation}

VSF member {id} going out of stack during ISSU operation: "{operation}", rebooting the stack

Unintentional failover detected during ISSU operation: "{operation}", rebooting the stack

ISSU complete timer expired. Rebooting switch {id} during ISSU operation: "{operation}

Member {member_id} interface {port_id} in VSF link {link} detected a peer {mac_address} with incompatible product type {prod_type}

Egress port shape rate {lowest_speed} update is failed to apply for interface {if_name}

ARP packet received from MAC {sender_mac} on VLAN {vlan_id}, untrusted port {port_name} with ip {ip_addr} is dropped as there is no corresponding entry in the IP binding table.

ARP packet received from MAC {sender_mac} on VLAN {vlan_id}, untrusted port {port_name} with ip {ip_addr} is dropped due to MAC mismatch in IP binding table.

Policy {policy_name} is of type {feature} and a valid feature pack is required to use the policy. The policy is currently in use without a valid feature pack.

L3 resources critical for neighbor and route forwarding are low. Used: {encaps_allocated}, Available: {encaps_free}

Interface {interface}: {fault} fault detected

Interface {interface}: {fault} fault detected and port disabled

Interface {interface}: {fault} fault detected, port is already disabled by another fault.

MACsec is operational on port {name} without a valid feature pack for {feature}.

IPv6 route prefix {prefix} is recommended for transit network use only. The traffic would be software routed. Routing performance to local destination addresses on this network may be impacted.

Resource '{resource}' usage is at {percent}% of capacity. Use 'show capacities-status' for more information.

Traffic for IPv6 route prefix {prefix} will be software routed and performance impacted if no other matching route prefixes from 0-64 for the same destination exist.

Container {name} image is unsigned and allowed by the user configuration

Container {name} image is unsigned and not allowed by the user configuration

PTP offset has reached beyond the threshold {low_limit} < {curr_offset} < {high_limit}

PTP offset has reached below the threshold {low_limit} < {curr_offset} < {high_limit}

PTP may not work as expected when PTP clock is BC and enabled on MCLAG {int_name}-{lag_name}.

Reached the maximum number of clients limit on the switch for device fingerprinting.

Reached the maximum clients limit of {client_limit} on the interface {interface} for device fingerprinting.

TELNET session from {ip_address} is rejected because maximum number of TELNET sessions is reached.

TELNET session from User {user_name} is closed because maximum number of sessions per user is reached.

CONSOLE session from User {user_name} is closed because maximum number of sessions per user is reached.

Hot-patch {patch_name} config mismatch, patch applied

Hot-patch {patch_name} is missing

Hot-patch {patch_name} was modified after it was parsed

Hot-patch {patch_name} could not be installed because a newer hot-patch has been, or will be, installed

Hot-patch {patch_name} could not be installed because another patch that is configured to be installed has the same timestamp

ISSU rollback timer expired. WARNING: previous software version {previous_software_version} was not found, booting system to active bank {active_bank} with {new_software_version} software version. This may cause issues with the current configuration.

HW Fault (Error {error_code}) detected on the switch. {impact_statement}. Contact support for assistance.

Chassis Reboot Requested: {reason}

Distributed Services Admission Rejected. Reason: {reason}

PSM coordinates mismatch. Active coordinates: {active_coordinates}, Configured coordinates: {configured_coordinates}.

App Recognition is operating without a valid feature pack.

App Recognition is blocked due to invalid or missing feature pack

{feature_pack_name} expired on {expiry_date}.

Feature pack {parameter_type} {subscription_parameter} does not match device {parameter_type} {device_parameter}

Feature pack file download failure

VSF member serial number {device_serial} not subscribed as part of installed feature pack.

Feature {feature_name} is operating in honor mode without a valid feature pack.

Connection to feature pack server lost and subscription for {feature_pack_name} cannot be validated. Subscribed features will continue to operate in honor mode.

No feature pack is installed. This device requires an Advanced or Premium feature pack to use advanced or premium features.

Advanced feature pack installed. This system requires a Premium feature pack to use all features.